Standard of Excellence: The Advantages of Flex and Rigid-Flex Circuits

Reading time ( words)

Since their introduction, flexible and rigid-flex circuits have been steadily moving from the fringe of electronic interconnection towards its center. Today, flex and rigid-flex circuits are found in countless products from the very simple to the highly complex. The reasons for this shift to the center are numerous; most of them are related to the advantages they offer. An examination of some of the benefits and advantages will make this clear.

A Remedy for Natural Packaging Problems

Flexible circuits are often chosen because they help to solve problems related to getting electronics inside the products they serve. They are a true three-dimensional solution that allows electronic components and functional/operation elements (i.e., switches, displays, connectors, and the like) to be placed in optimal locations within the product assuring ease of use by the consumer. They can be folded and formed around the edges to fit the space allowed without breaking the assembly into discrete pieces.

Reduced Assembly Costs

Prior to the broad use of flexible circuits, assemblies were commonly a collection of different circuits and connections. This situation resulted in the purchasing, kitting and assembly of many different parts. By using a flex design, the number of part numbers required for making circuit-related interconnections is reduced to one.

Eliminated Potential for Human Error

Because they are designed as an integrated circuit assembly with all interconnections controlled by the design work, the potential for human error in making interconnections is eliminated. This is especially true in the cases where discrete wires are used for interconnection.

Reduced Product Weight and Volume Requirements

Flexible circuits are appreciably lighter than their rigid counterparts. Depending on the components used and the exact structure of the assembly and the final product, they can save perhaps as much as 60% of the weight and space in the end-product as compared to a rigid circuit solution. Additionally, their lower profile can help a designer create a lower profile product than is possible with a nominal 1.5 mm-thick rigid board.

Facilitation of Dynamic Flexing

Nearly all flexible circuits are designed to be flexed or folded. In some unusual cases, even very thin rigid circuits have been able to serve to a limited degree. However, in the case where dynamic flexing of a circuit is required to meet the objectives of the design, flexible circuits have proven best. Modern disc drives, for example, require that a flexible circuit endure anywhere from tens to hundreds of millions of flexural cycles over the life of the product. Other products (laptop hinge circuits, for example) may only require thousands of the cycles, but it is the dynamic actuation capability enabled by the flex circuit that is key to its operation. 

Improved Thermal Management for High-Temp Applications

High temperatures are experienced both in assembly with lead-free solder and in the operation of higher power and higher-frequency digital circuits. Polyimide materials are well suited to the management of high-heat applications. Not only can they handle the heat, their thinness allows them to dissipate heat better than other thicker and less thermally conductive dielectrics.

Improved Aesthetics

While aesthetics may seem a low-order advantage, people are commonly influenced by visual impressions and frequently make judgements based on those impressions. Flexible circuit materials and structures look impressive both to the seasoned engineer and the layperson. It can make a difference in the decisions made in some applications, especially those where the user gets exposure to the functional elements of the product.

Increased Intrinsic Reliability

Flexible circuits help to reduce the complexity of the assembly and can reduce the number of interconnections that might be otherwise required with solder. Reduction in complexity is a key objective of a reliable design. With respect to the minimization of the number of solder interconnections, reliability engineers know all too well that most failures in electronic systems occur at solder interconnections. It follows naturally that a reduction in the number of opportunities for failure should result in a corresponding increase in product reliability.


Flex and rigid-flex circuits have significant advantages. There are many additional advantages that go beyond the short list provided here. What is important to remember is that most of the advantages stem from the versatility and unique integrative abilities these important members of the electronic interconnect family can offer.

The information contained in this column was taken from American Standard Circuits’ new eBook, The Printed Circuit Board Designer’s Guide to Flex and Rigid-Flex Fundamentals, published by I-Connect007. To download the book, click here.

Dave Lackey is vice president of business development at American Standard Circuits.


Suggested Items

Real Time with… AltiumLive 2020: Greg Ziraldo on a New Approach to DFM

10/08/2020 | I-Connect007 Editorial Team
Andy Shaughnessy speaks with Greg Ziraldo, senior director of operations at Advanced Assembly, about his AltiumLive panel, "Design With Manufacturing." Greg discusses things that designers and electrical engineers should keep in mind regarding assembly during the design process, as well as a few ideas that he hopes attendees will take away.

Real Time with… AltiumLive 2020: A Novel Idea—Design With Manufacturing

10/07/2020 | I-Connect007 Editorial Team
Andy Shaughnessy speaks with Jeremie Waller, senior electrical engineer at Quantel USA, about the panel he’ll be participating in during AltiumLive 2020 on design with manufacturing. He and panelists Gerry Partida of Summit Interconnect and Greg Zhiraldo of Advanced Assembly will discuss why designers need to see their fabrication and assembly providers as true partners, not just customers, and why communication is such a vital part of the design process.

The Cost of Inefficient Production of PCB Documentation

05/13/2020 | Mark Gallant, DownStream Technologies
The following article is an excerpt from Chapter 5 of the I-Connect007 eBook The Printed Circuit Designer’s Guide to… Documentation, written by Mark Gallant of DownStream Technologies.

Copyright © 2022 I-Connect007. All rights reserved.