Ledia 6 Direct Imaging System Offers Enhanced Speed and Precision


Reading time ( words)

I recently met with Ucamco’s Michel Van den heuvel, imaging product group director, to discuss the benefits of the Ledia 6 direct imaging system, which was introduced earlier this summer and features scan-alignment and improvements in registration and positioning accuracy.

Pete Starkey: Michel, it’s great to see you again.

Michel Van den heuvel: Hi, Pete. I’m happy to see you.

Starkey: One of your specialties is the Ledia direct imaging system, and I understand that there have been some new developments lately. Can you bring us up-to-date with the latest advances?

Van den heuvel: After Ledia 5, SCREEN Graphic and Precision Solutions introduced Ledia 6, which is a further improvement and development of the existing Ledia 5. Based on the feedback they had from customers, they have made further enhancements. One of the main improvements is a new camera-registration system. On the existing Ledia 5, they used step-alignment, which means that the table stops, switches on the light of the registration camera, and takes a picture of the fiducial, and then the table moves to the next fiducial and takes a picture again.

In the Ledia 6, they have introduced scan-alignment. The table moves at a constant speed and does not stop any more. When it needs to take a fiducial, it switches on the light and quickly takes the picture—it’s like a stroboscope effect—and switches the light on and off while the table keeps moving. Through software, they stitch all these pictures together and know exactly where all the fiducials are. It goes much faster because the table doesn’t need to stop.

Starkey: How accurately can you hold registration with this system?

Van den heuvel: Registration and positioning accuracy go together because, eventually, the result that the customer can see on the panel is positioning accuracy. With Ledia 6, we have improved positioning accuracy by 10% compared to the Ledia 5, and also improved registration accuracy by 20%.

In addition to the scan-alignment system, the width of the registration cameras has been doubled in size. Take the example where a solder mask panel has been routed after the panel has been made. This can influence not only the exact size but also the position of the fiducials towards the edge of the panel. With a smaller camera, this could previously result in sometimes missing a fiducial. The double-width scan-alignment camera will completely resolve this issue.

Another improvement, together with the scan-alignment, is that if you have multiple step-and-repeat single PCBs on the panel, and the fiducials of adjacent PCBs are within 12 millimeters of each other, our front-end software will automatically combine these fiducials and scan them with one camera in one go. Instead of doing two scans, you can combine it in one scan. Especially for step-and-repeats of panels, such as BGAs, this greatly improves scan-alignment time.

A further improvement involves new, stronger light sources that we built into the imaging heads. We made a change to the optics to make them capable of handling this stronger light source, which results in up to 25–30% throughput improvement. And the less sensitive is the material, the bigger the improvement you will notice.

Starkey: In a typical case with a solder mask, what would be the exposure time?

Van den heuvel: Exposing time depends on the panel. For 100 millijoules, the exposing time for a 610 x 457-millimeter [24 x 18-inch] panel side would be around 23.7 seconds compared to the previous 30.3 seconds, including four-point registration. Whenever you gain 6.6 seconds in a single run, that is a huge improvement.

Starkey: And your light sources can be tuned to achieve the optimum wavelength for the photo-initiator system in the solder mask?

Van den heuvel: Yes. The way the optical heads are designed, we can 100% independently adjust the different main wavelengths that we use: 365, 385, and 405 nanometers. We can independently adjust each wavelength from zero to 100% and tune to the solder mask at hand and achieve the best possible sidewall, reducing undercut to a minimum.

Starkey: Have you already launched the Ledia 6 into the market?

Van den heuvel: Yes, we have. The first systems in Europe have been sold this year, and two of them have already been installed at ICS in Italy and Optiprint in Switzerland. The results have been as we expected, and our clients are delighted with the outcome. Next week, we will install a third one at Eurocircuits in Hungary.

Starkey: That is splendid! I wish you every success with the system. Thank you very much for your time.

Van den heuvel: Thank you, Pete.

Share




Suggested Items

EIPC Summer Conference 2022: Day 2 Review

06/29/2022 | Pete Starkey, I-Connect007
Örebro, Sweden on June 15 brought a bright and early start to Day 2 of the EIPC Summer Conference for those who had enjoyed the previous evening’s networking dinner, but had resisted the temptation to over-indulge or to carry on their long-awaited catch-up conversations with old friends into the small hours. All but a few were in their seats for 9 a.m., awake and attentive for Session 4 of the conference, on the theme of new process technologies, moderated by Martyn Gaudion, CEO of Polar Instruments.

Technica Heats Up ROI Discussion

05/17/2022 | I-Connect007 Editorial Team
The I-Connect007 Editorial Team speaks with Technica’s Frank Medina, Ed Carrigan, and Jason Perry about trending hotspots that provide the PCB fabricator a high return on investment (ROI). A theme that carries throughout the conversation is that traditional methods for calculating ROI are being replaced by models that include more qualitative factors.

EIPC Technical Snapshot: Supporting Autonomous Driving

05/12/2022 | Pete Starkey, I-Connect007
EIPC’s 17th Technical Snapshot webinar on May 4 focused on developments in automotive electronics, particularly on advances in the technologies required to support the evolution of autonomous driving. The team brought together two expert speakers to present their detailed views on topics encompassed within “CASE,” the acronym that appears to be taking over the automotive industry.



Copyright © 2022 I-Connect007. All rights reserved.