-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueThe Sustainability Issue
Sustainability is one of the most widely used terms in business today, especially for electronics and manufacturing but what does it mean to you? We explore the environmental, business, and economic impacts.
The Fabricator’s Guide to IPC APEX EXPO
This issue previews many of the important events taking place at this year's show and highlights some changes and opportunities. So, buckle up. We are counting down to IPC APEX EXPO 2024.
Getting to Know Your Designer
In this issue, we examine how fabs work with their design customers, educating them on the critical elements of fabrication needed to be successful, as well as the many tradeoffs involved. How well do you really know your customer? What makes for a closer, more synchronized working relationship?
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - pcb007 Magazine
Exploring High Density With Axiom
May 6, 2022 | I-Connect007 Editorial TeamEstimated reading time: 3 minutes
Nolan Johnson and Barry Matties talk with Axiom’s Rob Rowland and Kevin Bennett about the current high-density challenges facing EMS manufacturing. In this interview, Bennett and Rowland zero in on component packaging and feeder technology as critical areas in need of improvement.
Nolan Johnson: Rob, please introduce us to Axiom.
Rob Rowland: Axiom has been an EMS provider for about 30 years. We primarily focus on military, aerospace, space products, and any other high-reliability application type of customers, building the more complex, high-density type of boards. Kevin has been doing placement for over 20 years, both as a machine programmer and a process engineer. We probably handle a wider diversity of unique components than many companies doing board build. Our board sizes range from what you would call a memory module size, up to boards in the 18-by-20-inch size range, so we handle a large variety of different sizes.
Johnson: Is it fair to assume that it’s a mostly high-mix, low-volume setup?
Rowland: Yes. Our expertise is the higher mix, lower volume, with a typical run in the 30- to 50-board range. We have a couple of runs where we’re building in the hundreds, and occasionally into the thousands, but it’s usually jobs fewer than 100 boards. One interesting aspect when talking about placement machines is that most companies in the U.S. are dealing with higher mix, lower volume.
It’s fair to say there’s a big distinction between what you need to do for different production mixes. As I talk with my peers in the industry, one of our biggest challenges for the higher mix, lower volume placement is component packaging.
Packaging—Tape, Reels, and Tubes... Oh My!
Barry Matties: When we talk about packaging, do you mean part of the components?
Rowland: In this case, we’re specifically talking about tape and reel vs. matrix tray vs. tubes. The ideal scenario if you’re running high volumes is to buy full-size reels. When you’re in the high-mix business, you’re typically dealing with much shorter strips of tape, and not all the machines on the market are well-designed to deal with that. It’s a major challenge for domestic companies, and one that the placement industry has not stepped up to address as much as I would like. We had to develop a process that enables us to deal with shorter strips of tape; it’s typically one of our bigger headaches from a board build standpoint.
Johnson: Is that sort of packaging challenge worse when you’re dealing with very small components or is it consistent across the board?
Kevin Bennett: It’s worse when you’re dealing with smaller components, because there are different methods for loading them onto the placement machine. The components are presented in the pockets of the carrier tape with cover tape over the top of each pocket to keep them from falling out. When you have a short strip of tape, there needs to be enough carrier tape length for the feeder to advance correctly. In that case you must prep the strip with an extra length of cover tape, so the mechanism that peels the cover tape back will expose the component for the nozzle to pick from.
If you’re placing short strips of tape on a matrix tray platform, the entire length of cover tape needs to be peeled back before attempting to pick. If the short strip contains small components, a slight bump could cause all the components to come out of the carrier tape with potential loss due to attrition.
To read this entire conversation, which appeared in the May 2022 issue of SMT007 Magazine, click here.
Suggested Items
Absolute EMS Successfully Recertifies ISO 9001:2015 and AS9100 Standards
03/26/2024 | Absolute EMS, Inc.Absolute EMS, Inc., an award-winning EMS provider of turnkey contract manufacturing services, is proud to announce the successful recertification of its ISO 9001:2015 and AS9100 Rev D SAE International Aerospace Standards.
Arlon EMC Receives IPC-4101 QPL Recertification
03/20/2024 | Arlon Electronic MaterialsArlon Electronic Materials has successfully completed an intensive two-day recertification audit by IPC Validation Services that examined Arlon’s manufacturing processes and testing procedures to assure that they are in conformance to the requirements of IPC-4101E-WAM1, the Specification for Base Materials for Rigid and Multilayer Printed Boards.
Northrop Grumman Honors Suppliers for Excellence
03/14/2024 | Northrop GrummanNorthrop Grumman Corporation honored more than 70 suppliers for their outstanding contributions in 2023. In an annual recognition event, the companies included women-, minority- and veteran-owned small businesses as well as those operating in underdeveloped areas.
Cicor Acquires TT Electronics IoT Solutions
03/04/2024 | Cicor Technologies Ltd.The Cicor Group has signed an agreement to acquire TT Electronics IoT Solutions Ltd, with three production sites in the UK and China.
AEM, Texas Aerospace Technologies Bolster Partnership for Latin America
02/26/2024 | AEM Corp.Canadian avionics manufacturer, Anodyne Electronics Manufacturing Corp. (AEM), is pleased to announce a partnership expansion with Texas Aerospace Technologies, a subsidiary of Texas Aerospace Services, to add AEM’s new MTP136D modern panel-mount P25 VHF FM Forest Service radio to its lineup of product offerings for their Latin American customers.