Signal Loss


Reading time ( words)

Signal loss (attenuation) in transmission lines can have a variety of causes.

  • Radiative loss
  • Coupling to adjacent traces
  • Impedance mismatches
  • Conductor loss
  • Dielectric loss

According to Reference 1, radiative loss is only a small component of loss contributors. Coupling to adjacent lines, on the other hand, can cause signal rise time degradation. It can be modeled quite accurately and proper circuit layout can minimize it.

Impedance Discontinuities

Impedance discontinuities (i.e., variations or changes) along the transmission line cause signal degradation. The cross section of the conductor should not change along the transmission line. Such changes affect the impedance. They can be caused by plating height variation, or etch non-uniformity, or localized imperfections such as conductor “dish down” or “mouse bites.”

Less understood is the change of the properties of the dielectric that contributes to impedance mismatch, namely the dielectric constant.

Typical dielectric structures are glass weave, reinforced epoxy resins. Both the dielectric constant of the resin as well as that of the glass are bulk properties of the materials and are quite constant throughout the material. The dielectric constant of FR-4 resin is about 3.2 and the dielectric constant of glass is about 5.6. Since the glass weave reinforcement has a pattern, there are glass-rich and glass-lean domains in the dielectric. Therefore there are domains of higher and lower dielectric constant surrounding the signal path, which means the impedance changes along the signal path (i.e., there are impedance discontinuities). If a transmission line runs parallel, and on top of a glass fiber strand, or along a resin-rich area between glass fibers, then the dielectric environments of these two lines are noticeably different, which unfortunately is the case most of the time as laminate is sheared parallel to the weave pattern, and conductor lines tend to run in the same direction. Angling the transmission lines relative to the weave pattern will improve the situation by randomizing the glass/ resin concentration differences along the transmission path. References 2 and 3 have studied this problem area.

Read the full article here.

 

Editor's Note: This column originally appeared in the January 2015 issue of The PCB Magazine.

Share




Suggested Items

EIPC Winter Conference 2023, Day 2 Review

02/28/2023 | Pete Starkey, I-Connect007
Day 2 of the EIPC Winter Conference at the Groupama Stadium in the Décines-Charpieu region of the Metropolis of Lyon in eastern France included a privileged visit to the Bugey Nuclear Power Plant for those who were registered and passed their security clearance. Such was the interest that the party was split into morning and afternoon groups. EIPC board member Martyn Gaudion, CEO of Polar Instruments, made a fine job of moderating Session 6 twice over.

EIPC Winter Conference 2023: Day 1 Review

02/27/2023 | Pete Starkey, I-Connect007
The EIPC Winter Conference returned to the Metropolis of Lyon in eastern France this month. In 2018, the venue was Villeurbanne in the Auvergne-Rhône-Alpes region. Five years later the setting was the Groupama Stadium in Décines-Charpieu, and leaders of the European printed circuit community gathered in expectation of a spectacular programme of 16 presentations, a visit to a nuclear power station, and an invaluable networking opportunity. They weren’t disappointed.

Ventec: Contextualizing the CHIPS Act

01/05/2023 | Nolan Johnson, I-Connect007
Nolan Johnson hears from Alun Morgan, Technology Ambassador at Ventec, and Mark Goodwin, Ventec’s COO, about the benefits and risks posed by new PCB-oriented legislation in the U.S. and Europe. Faced with a rapidly consolidating industry, especially in the face of mounting pressure from the Russia-fueled energy crisis, government intervention is a welcome prospect—as long as legislators are committed to addressing the full scope of the issue, including the supply chain’s migration to Asia. Ventec is hopeful that, having been called on to educate government officials on the challenges facing the industry, they will help spur future legislative changes that will protect and grow the industry’s interests.



Copyright © 2023 I-Connect007 | IPC Publishing Group Inc. All rights reserved.