Material Witness: How About that Technical Roadmap!


Reading time ( words)

You may remember the movie What About Bob?  If you do, you may recall the scene in which Bob (played by Bill Murray) confronts his psychiatrist (played by Richard Dreyfuss) and emotes, “I need! I need! I need! Gimme! Gimme! Gimme!”

As I thought recently about some of the drivers that IPC and others have incorporated into their technical roadmaps (not that they all are new by any means, but each time they come out, some of the technical parameters are squeezed a bit harder) I feel a bit like that befuddled psychiatrist. It’s tough figuring out how to make materials that meet all the “I need!” and “Gimme!” requirements and drivers while still satisfying the UMS (Universal Material Specification):  “Low dielectric constant, low loss, high performance and free.”

Consider just a few of the obvious considerations: 

  • Thermal dissipation increasingly drives design.
  • Maximum board operating temperatures are rising (watt density).
  • IC’s are going 3D resulting in much higher density devices.
  • Fine line/space circuitry will continue to be critical as HDI demands increase.
  • Mechanical drilling is being challenged for both through holes and buried/blind vias.
  • Micro via technology and laser drilling will continue to push for smaller diameters.
  • Higher frequencies are increasingly necessary as transmitted data volume increases.
  • Enhanced glass styles (flat glass) will help signal stability at microwave frequencies.
  • Land diameters will shrink as device I/O density increases.
  • Registration on larger panels (fine lines and small lands) will increasingly be an issue.
  • “Green” requirements will continue to be pushed – albeit at the “right price.”
  • The percentage of assembled PWBs required to be recyclable will increase.
  • Dielectric properties will be increasingly important as frequencies rise.
  • Digital and RF/microwave materials will converge with conventional materials.
  • Data demand will push the limits of current 3G and 4G build-outs (resulting in more HDI demand and at higher frequencies).

 

There are a variety of design, material and manufacturability issues that these tightening requirements should suggest to PWB raw material suppliers. Just a few: 

  • Thermally conductive materials will continue to become a greater part of the PWB package. Heat sinks alone will no longer do the whole job as density of device mounting becomes greater and greater, and consumers want an infinite amount of functionality in smaller and smaller packages. (My maturing—i.e., old—eyes already revolt at the idea of watching streaming movies on a 4 cm x 6 cm screen however HD the resolution may be.)  Keeping device temperatures down becomes critical, as every 10oC of lowered temperature doubles the mean time between failures (MTBF).  Thermally conductive microwave and RF materials will also find increasing usage as less thermal variability at the device level means more signal stability. 
  • The implications in building multilayer microchip IC’s are also huge, in that the density of features on a PWB will increase substantially (all that functionality eventually needs to reach the real world of people with large (relative to the IC anyway) hands and the need for stuff they can handle. My 17-year-old granddaughter texts at about a gazillion wpm, but my old, larger fingers have trouble touching only one of those little bitty keys at a time. And we want things smaller still?  (Maybe voice- or thought-activated electronics will eventually allow some of these barriers to be eliminated.) One of the obvious implications of increasing HDI on PWBs is that registration, always an issue with lots of holes in large panel sizes will become a bigger gorilla. This will become even more critical as land sizes and hole diameters shrink, and more and thinner layers are needed to get the necessary signal density. 
  • Environmental issues, whatever any of us may think about the validity of the science behind some of the evolving requirements, will continue to require material suppliers to produce products that are “greener” (that is, having low levels of halogens and other banned chemicals) and more environmentally sustainable (including recycling, recovery of metals, recovery of energy from hydrocarbon based components, etc.). That includes finding sustainable substitutes for traditional brominated flame retardants and developing low cost materials that will survive in lead-free soldering environments. What solder systems may eventually become “standard” is not yet clear, but I have a sort of back of my mind worry that my new $2,500 Mitsubishi 3D HDTV will suddenly go “poof” and shut down because of tin whisker growth from the “environmentally safe” solder being used. The military OEMs are leery of newer solders for several reasons. All of us in the materials business need to wonder if the improved solutions to green and environmental issues have longer term issues (technical and political) we haven’t even considered yet. Are phosphorus-based flame retardants actually safer than halogens?

  • The basic multilayer PWB is not going to go away soon. It remains needed to connect all this incredible functionality to the real world in packages that are suitable for human interconnection. When we get microchip ICs implanted in our brains that can project info into our ears and eyeballs directly (a super Google Glass?) and interconnect via microwaves with equally small chips in desktop computers that can be a few cubic inches in size, then maybe the PWB will start to fade away. But for now we need to interact with a technologically very adaptive world by tuning materials to the current needs set.

The “needs” and “gimmes” will never go away, and hopefully there will be common sense applied at the government regulatory level in the U.S. and elsewhere, though common sense and government sometimes to be antithetical. But as a materials guy, I see the challenges of the early 21st century demanding that we continue to evolve better and more cost effective materials, and to fine tune the ones we have. Our success at being flexible and adaptable will be a major definer of our success in the next few interesting years.

Chet Guiles is a consultant for Arlon Electronic Materials Division.

 


About Arlon Arlon Electronic Materials Division, now part of Rogers Corporation (www.rogerscorp.com), is a major manufacturer of specialty high performance laminate and prepreg materials for use in a wide variety of printed circuit board (PCB) applications and in several distinctive markets. http://www.arlon-med.com

Share

Print


Suggested Items

Real Time with… AltiumLive 2020: Vince Mazur Previews New Design Rule Features

11/03/2020 | I-Connect007 Editorial Team
Altium Technical Marketing Manager Vince Mazur discusses his presentation at the recent AltiumLive, which focused on updates to Altium Designer's approach to creating design rules and constraints. Vince explains that these features will be more intuitive for the user, and the update, which is currently in beta, will be released in the future. The company is shifting from “rule-centric” design rules features to capabilities that are more “design-centric,” with applicable rules for each object available at one click.

Real Time with… Altium Live Europe 2020: Rick Hartley’s Secrets of PCB Optimization

10/29/2020 | Pete Starkey, I-Connect007
As Lawrence Romine said in his introduction, “There’s that moment when you sit in the crowd and hear Mr. Rick Hartley speak that you know you’ve arrived in PCB design.” With 50 years in the industry focused on circuit and PCB design—and as a specialist in EMI, noise, and signal integrity issues—Rick Hartley was invited to talk about PCB optimization. Pete Starkey provides an overview of the presentation.

Just Ask Happy: The Exclusive Compilation

08/13/2020 | Happy Holden, I-Connect007
We asked for you to send in your questions for Happy Holden, and you took us up on it! We loved them so much, and we know that you did too, so we’ve compiled all 21 questions and answers into one document for easy reference.



Copyright © 2020 I-Connect007. All rights reserved.