Stepping Up To Laser Processing for Flex, Part 1: Opportunities and Implications


Reading time ( words)

This six-part series will examine how to effectively supplement your flex production capabilities with laser processing.

Market demand for smaller, faster, wearable, lighter and more powerful devices continues to keep PCB manufacturers scrambling to keep up as they evolve and adapt their manufacturing capabilities to meet changing customer needs. But keeping up with the dizzying pace of change in the world of PCB manufacturing need not be a daunting task. Employing laser technology is one of the best ways to stay current, as it enables printed circuit manufacturers to achieve manufacturing flexibility and agility, with more accurate and/or smaller features than is possible with traditional processes.

As highlighted in Figure 1, there are several steps in the flexible circuit manufacturing process where laser processing can play a significant role. In this series, we will focus on the laser micromachining processes related to drilling, coverlay cutting and circuit singulation using general laser micromachining systems. Keep in mind that, although this series deals primarily with flex, many of same laser processing principles discussed also apply to rigid boards—and even to LDI.

 laser_tech.JPG

Figure 1: The role of laser technology in the flex processing manufacturing flow.

When is the Right Time to Adopt Laser Micromachining?

Printed circuit manufacturers typically invest in laser micromachining systems when current mechanical processing capabilities can no longer address the processing accuracy and quality dictated by size constraints and newer materials. Mechanical punching, routing, and drilling are either no longer feasible or simply not a cost-effective solution due to many of the following issues:

  • Features become too small or too complex for drill/routing bit diameters and/or die punch manufacturing capabilities
  • Trace width/spacing requirements require via pads to shrink beyond mechanical drilling registration capabilities
  • Part tolerances require machining accuracies beyond mechanical processing capabilities
  • The number of vias per panel increases sufficiently to make mechanical drilling less cost effective than laser drilling.
  • Customer demand includes blind via processing in thin flex material beyond the depth control capabilities of mechanical drills.
  • High product mix and/or fast turnaround time requirements become incompatible with the long lead times and expense associated with fabricating dies for coverlay cutting and circuit singulation

If some of these issues sound familiar, it’s probably time to consider laser processing. But before launching into that endeavor, take the time to learn about the opportunities and implications associated with laser processing. It can pay big dividends, but to get optimal results there are some approaches and best practices that you should be aware of.

About This Series

In each future installment of the Stepping up to Laser Processing for Flex series, we will arm you with information you need to investigate the advantages of FPC laser processing and the role it can play in optimizing your processing capabilities. Upcoming installments will cover the following:

  •  Calculating and Optimizing Production

How do you calculate and optimize total system cost of ownership and cost per panel? We will provide an overview of the high-impact profitability factors in choosing and running your system.

  •  Readiness and Site Preparation

How do you ensure that your facilities are ready for the introduction of laser processing? Find strategies for addressing shop floor concerns such as HVAC, temperature control, debris removal capabilities, power requirements and more.

  • Installation, Training, and Initial Operation

How do you get your new system installed and processing those first runs?  We will cover installation best practices, system verification testing, training and safety.

  •  Process Development

How do you develop your process library? Learn several best practices, tips and tricks for typical flexible circuit laser processes.

  • Maintenance and Servicing

How do you minimize system maintenance and repair costs while prolonging its useful life? We’ll examine best practices and considerations related to the “care and feeding” of your laser processing machine.

Mike Jennings is director of product marketing with ESI’s Industrial Products Division.

Patrick Riechel is product manager for ESI’s flexible circuit micromachining tools.

Share

Print


Suggested Items

Predicting a ‘Roaring Twenties’ Innovation Boom

02/24/2021 | Hailey Lynne McKeefy, Freelance Journalist and Supply Chain Specialist
The 2020s have not started as anyone would have wished. The COVID-19 pandemic has exposed weaknesses in supply chains and in global manufacturing, yet this could still be the most innovative decade ever.

Kemmer Praezision Partners with Insulectro

02/04/2021 | Nolan Johnson, PCB007
In this interview, Nolan Johnson and Gregor Dutkiewicz discuss Kemmer Praezision, their new working partnership with Insulectro, and some of the recent market challenges in mechanical drill bit technology.

IPS Expanding to Accommodate Growing Market

11/24/2020 | Barry Matties, I-Connect007
I recently had the opportunity to visit IPS in their Cedar City, Utah, facility, where Mike Brask, founder and president of IPS, shared his business strategy and gave me a tour of the expanding manufacturing facility. IPS produces a wide range of PCB manufacturing equipment, including plating, DES, VCM, VRPs, ventilation, and spare parts for older equipment.



Copyright © 2021 I-Connect007. All rights reserved.