The Application of Advanced Ultrasonics in Metal Plating Processes


Reading time ( words)

Most surface modification chemical treatments by their very nature contain hazardous and oxidising chemicals; there is a major concern that these chemicals are used maliciously with the intent to manufacture explosives or formulate poisons to harm the public. Cyanide-based plating solutions and high concentrations of hydrogen peroxide used in current techniques are a significant use of these materials in industry.

The use of cyanide and hydrogen peroxide is concentrated in a few industries: large polymer manufacturers, chemical manufacturers, and surface finishing companies. Surface finishing/PCB manufacturing is a particular risk as in general the sites where these processes are run are small, distributed and less secure than large chemical plants. Consequently, amounts of these dangerous substances are found across the UK with varying and sometimes limited control over their use, representing a significant risk.

Barriers to implementation of cyanide-free plating solutions are related to quality of product and operational requirements. Introduction of the novel ultrasound technology can overcome these barriers, but must be validated on full scale processes and over a range of plating systems.

The introduction of ultrasound to current industrial protocols has been demonstrated in the first phase of the Reprime project to allow the removal of cyanide from metal plating processes, and significantly reduce the amount of hydrogen peroxide use. A small test plating line was set up featuring an ultrasound tank in which barrel plating, vat plating or PCB etching could be performed.

reprime1.JPG 

Figure 1: Ultrasound reactor showing ultrasound transducers (left) and barrel plating (right).

Results from zinc plating trials on fixings, showed that cyanide free solutions could be improved in terms of the weight addition and the coverage consistency with appropriate application of ultrasound. The technique particularly aids coverage when used on unusual shapes and through holes which are typically problematic with cyanide free solutions.

reprime2.JPG 

Figure 2: Improved plating rate on hex-nuts in acid based zinc plating solutions when ultrasound is applied.

Ultrasound was shown to reduce the levels of hydrogen peroxide required in etchant solutions used in PCB manufacturing. However, the biggest improvements were seen when considering bath life. Baths treated with a particular configuration of ultrasound could perform for significantly longer timescales without performance degradation. Therefore, bath chemistry can be replenished at a less frequent rate, reducing chemical use and handling requirements.

reprime3.JPG              

Figure 3: PCB test materials untreated (left) and treated (right) with a hydrogen peroxide based etchant.

To go beyond the current process development and achieve impact in industry, the scope of work must be increased to test at an industrially relevant scale and to broaden the range of processes covered. Work is currently focussed on making cyanide free technology more attractive on performance grounds to overcome barriers to implementation. Overall aims of the project are as follows:

  • Demonstrate that zinc plating can be achieved at a scale relevant to industrial systems
  • Ensure technology can be easily used with existing equipment
  • Extend plating trials to other cyanide plating systems such as copper, gold and silver to cover the bulk of the industrial processes
  • Carry out hydrogen peroxide etch at full PCB manufacturing scale and prolonged bath life trials
  • Work with industry bodies such as the Surface Engineering Association (SEA) and ICT (institute of Circuit Technology) to engage and inform industry

There is huge potential for this technology to make a positive impact on the reduction of dangerous chemicals with over 1000 factories in the UK operating surface finishing or PCB manufacturing processes. The output from these industries are cross-sectoral, including vast markets within the automotive, aerospace, and electronics sectors. It is hoped that through this research work, a viable technical solution can be applied through this industry.

Stuart Dalrymple is a project manager at C-Tech Innovation with experience running research projects in the areas of process engineering, surface finishing and environmental assessment.

Share




Suggested Items

Plating on Silver: What’s Old is New Again

07/07/2022 | Denis Jacques, Technic Inc.
About three decades ago, immersion silver, a nitrate-based process, gained a lot of market share in the world of PCB final finishes. More economical than ENIG, flat, solderable, and conductive, it had everything going for it—everything but corrosion resistance in a harsh environment, that is. Champagne voids were also an issue, along with line reduction. But the worst drawback, the characteristic that made the part short over time, was creep corrosion. A build-up of copper sulfide salt that grows in contact with a sulfur-rich environment, heat, and moisture resulted in failures in the field. This was enough to scar the process for good.

EIPC Summer Conference 2022: Day 2 Review

06/29/2022 | Pete Starkey, I-Connect007
Örebro, Sweden on June 15 brought a bright and early start to Day 2 of the EIPC Summer Conference for those who had enjoyed the previous evening’s networking dinner, but had resisted the temptation to over-indulge or to carry on their long-awaited catch-up conversations with old friends into the small hours. All but a few were in their seats for 9 a.m., awake and attentive for Session 4 of the conference, on the theme of new process technologies, moderated by Martyn Gaudion, CEO of Polar Instruments.

EIPC Summer Conference 2022: Day 1 Review

06/28/2022 | Pete Starkey, I-Connect007
At last, a live EIPC conference and this time in the Swedish city of Örebro, “where history and contemporary culture converge,” a pleasant and convenient location for an event that included a privileged visit to the Ericsson facility in Kumla. Around 100 delegates made the journey and the Örebro Scandic Grand Hotel was an excellent conference venue for the June 14-15 conference.



Copyright © 2022 I-Connect007. All rights reserved.