-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Chapter 1 Excerpt from the Book ‘Thermal Management: A Fabricator's Perspective’
December 8, 2020 | Anaya Vardya, American Standard CircuitsEstimated reading time: 3 minutes
Chapter 1
Heat cannot be efficiently exchanged with stagnant air surrounding a hot device; however, it can be transferred away from the electronic component to the PCB using thermal vias. A thermal via is a good conductor of heat that runs between the top layer and bottom layer of the PCB, dissipating heat through simple conduction. In simple terms, thermal vias are plated holes located under, or electrically connected to, a surface-mounted heat source on a PCB that allows heat transfer through the hole (Figure 1-1).
The efficient vertical heat transfer through thermal vias in the Z-axis is especially important to allow heat distribution over large areas of the PCB in the X-axis. Thermal vias run the design continuum from simple through-hole vias connecting the two external layers to complicated buried and blind microvias in stacked or staggered structures.
It should be noted that thermal vias, while the least expensive method of thermal management, are not always effective. It depends on the distribution of heat sources, the layout of the planes, and the cooling conditions on the bottom side. Also, if the air on the other side is stagnant, thermal vias are almost only useful with a heat sink on the bottom side.
This chapter will address three common thermal via designs: thermal via arrays, copper planes, and via fill.
Thermal Via Arrays
The premise that the thermal loss of a component is primarily transferred to the base of the package allows for the design integration of a path for heat dissipation into the physical PCB. A very common and cost-effective approach is to place an array of PCB thermal vias directly underneath the component (Figure 1-2). After the component is soldered to the PCB, the base of the component is connected to the thermal vias on the top side of the PCB.
Heat is then dissipated through these thermal vias down to the bottom side of the PCB. The efficiency of heat transfer through thermal vias is directly related, but non-proportional, to the amount of copper available to dissipate the heat. That being said, in many cases, the use of standard open vias (unfilled) may not provide the required thermal transfer on their own as the amount of actual copper is limited to the circumferential sides of the via. The most common method to improve this thermal performance is to combine the thermal vias with other thermal management techniques, such as copper planes, via fill, or heat sinks. A thermal simulation should be done.
Design Considerations
A design consideration is that adding unfilled (open) plated through vias to the SMT pad (via-in-pad) creates some challenges because it may result in a solder wicking issue during assembly. This means that solder tends to flow (wick) down into the vias during the assembly reflow process, which may create solder voids on the pad. If open thermal vias need to be used, there are some things that can be done to minimize this problem: For example, use a small via diameter. The surface tension of solder limits the amount of solder wicking on smaller vias. With 0.3 mm or smaller via diameter, the solder wicking can be reduced. You can also fill the vias with thermally conductive materials. It eliminates the solder wicking but adds cost and an extra manufacturing step (see the via fill section).
Further advice includes the following:
- Eight mils (0.2 mm) is the typical minimum mechanical drilling size. Twelve mils (0.3 mm) is more common and lower cost if the design will permit
- IPC-6012 specifies a minimum 20-µm (0.8-mil) copper plating thickness for a Class 2 PCB, but manufacturers target 25 µm (1 mil). As discussed earlier, the more copper thickness plated in the via, the more heat can be transferred
- PCB thickness may have an impact on the thermal via performance
To download The Printed Circuit Designer’s Guide to…Thermal Management: A Fabricator’s Perspective, click here. You can also view other titles in our full library. Check out other books from American Standard Circuits, including The Printed Circuit Designer’s Guide to… Fundamentals of RF/Microwave PCBs and Flex and Rigid-Flex Fundamentals.
Suggested Items
Hentec/RPS Publishes an Essential Guide to Selective Soldering Processing Tech Paper
04/17/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, announces that it has published a technical paper describing the critical process parameters that need to be optimized to ensure optimal results and guarantee the utmost in end-product quality.
Empowering Electronics Assembly: Introducing ALPHA Innolot MXE Alloy
04/16/2024 | MacDermid Alpha Electronics SolutionsIn the rapidly evolving electronics industry, where innovation drives progress, MacDermid Alpha Electronics Solutions is committed to setting a new standard. Today, we are pleased to introduce ALPHA Innolot MXE, a revolutionary alloy meticulously engineered to address the critical needs of enhanced reliability and performance in modern electronic assemblies.
New Book on Low-temperature Soldering Now Available
04/17/2024 | I-Connect007I-Connect007 is pleased to announce that The Printed Circuit Assembler’s Guide to… Low-temperature Soldering, Vol. 2, by subject matter experts at MacDermid Alpha Electronics Solutions, is now available for download.
Inkjet Solder Mask ‘Has Arrived’
04/10/2024 | Pete Starkey, I-Connect007I was delighted to be invited to attend an interactive webinar entitled “Solder Mask Coating Made Easy with Additive Manufacturing,” hosted by SUSS MicroTec Netherlands in Eindhoven. The webinar was introduced and moderated by André Bodegom, managing director at Adeon Technologies, and the speakers were Mariana Van Dam, senior product manager PCB imaging solutions at AGFA in Belgium; Ashley Steers, sales manager at Electra Polymers in the UK; and Dr. Luca Gautero, product manager at SUSS MicroTec Netherlands.
TE Connectivity Orders Hentec Industries/RPS Automation Pulsar Solderability Testing System
04/09/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, is pleased to announce that TE Connectivity has finalized the purchase of a Pulsar solderability testing system.