-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueAdditive Manufacturing
In this month’s issue, we explore additive manufacturing technology for the PCB fabricator: where it stands today, the true benefits, and where it seems to be headed.
The Growing Industry
In this issue of PCB007 Magazine, we talk with leading economic experts, advocacy specialists in Washington, D.C., and PCB company leadership to get a well-rounded picture of what’s happening in the industry today. Don’t miss it.
The Sustainability Issue
Sustainability is one of the most widely used terms in business today, especially for electronics and manufacturing but what does it mean to you? We explore the environmental, business, and economic impacts.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - pcb007 Magazine
The Institute of Circuit Technology Annual Symposium 2018
June 18, 2018 | Pete Starkey, I-Connect007Estimated reading time: 13 minutes
A test board had been designed using a composite of standard IPC coupons in 0°, 45° and 90° orientations in a 10-layer stack-up, featuring 100-ohm edge-coupled differential strip-lines with 100/150 micron and 100/100 micron track/gap, and single-ended strip-lines with 175 micron 50 ohm, 75 micron 75 ohm, and 195 micron 50 ohm tracks.
Two panels were manufactured using the MuTracx inkjet printer, and two using LDI and photoresist. Track widths and edge waviness were measured on innerlayers before and after etching. Impedances were measured with a time-domain reflectometer, and microsections were made for measurement of dielectric and copper thickness. Veerman showed comprehensive test data.
From the results it was clear that there was no strong correlation between cross-section data and impedance. Impedance correlated with average track width and, significantly, no difference was observed between LDI and inkjet imaging technologies in terms of the effect of track-edge waviness. Dielectric thickness had the most dominant effect, together with the effect of resin-to-glass ratio on dielectric constant.
Before the commencement of the afternoon session, the indefatigable efforts of Len Pillinger over many years of acting as the link between the Institute and the standards committees were recognised in the award of Honorary Fellowship, presented by ICT Chairman Professor Andy Cobley.
The programme re-commenced with a discussion of advances in direct imaging technology from Michel van den Heuvel, imaging group director at Ucamco.
The trend had been to move from high-pressure mercury lamps to UV-LED light sources, particularly for solder mask exposure. The state-of-the-art was a broad-multi-wavelength system, with peaks typically at 365, 385 and 405 nanometres, operated simultaneously and with the ability to control individual intensities to optimise the mix to suit individual solder masks.
The shorter wavelengths favoured the polymerisation of the surface of the solder mask, the medium wavelengths penetrated deeper into the thickness, and the longer wavelengths ensured good polymerisation at the copper surface. The optimised combination gave a very uniform through-cure, resulting in very straight sidewalls after development and the capability to reliably resolve 50-micron solder dams without undercut, as well as shortening the exposure time and hence increasing throughput. The system also gave very good results with black solder masks.
Van den Heuvel explained that the Ledia equipment supplied by Ucamco had many advanced features: its autofocus capability could compensate for panel warpage of up to 800 microns; its automatic imaging-head calibration facility ensured the position of each imaging head in relation to the other five heads, resulting in perfect stitching of the image and compensated for minute dimensional changes in the machine due to temperature variations. It also had a range of innovative automatic alignment features to compensate for substrate distortion. To fulfil the requirement for complete traceability, there was the facility to mark every individual PCB image with a unique identity, human- or machine-readable, which could also incorporate scaling information if required.
Peter Alliston, VP sales for Orbotech West, discussed the trends currently driving PCB technology, and described how leading suppliers of imaging and inspection tools had responded with developments in the capability of their equipment. He identified four market sectors: Internet of Things and 5G infrastructure, smartphones, automotive, and Industry 4.0 and robotics.
High-frequency PCB designs for 5G wireless broadband operating in the millimetre wave spectrum would demand strict impedance control at the 5% tolerance level, and low-loss materials. It was forecast that there would be 30 billion connected devices by 2020 and 75 billion by 2035.
Smartphones were leading mass production technology, with trends to 20X faster processing and communication rates together with increased battery capacity, to support augmented reality, artificial intelligence, and biometric and medical sensing. As batteries got larger, the space available to accommodate the PCBs got smaller, forcing an increase in interconnection density towards 20-micron lines and spaces that could not be achieved by established HDI processes. The technology was trending towards substrate-like-PCB (SLP), produced by modified semi-additive processing (mSAP). The use of flex in smartphones was increasing—up to 20 flex circuits in every unit, and there was a move towards roll-to-roll manufacture for more cost-effective production
Rapid development continued in automotive electronics, and the requirements of safety and autonomous operation were driving advances in sensor technology—radar, lidar, cameras, long range radar, and ultrasonics, many of which needed 5G connectivity. The use of HDI was increasing, and the automotive sector was forecast to represent 15% of the total HDI market by 2020.
Enormous investment was being made in automation, smart data exchange and cyber physical systems, and the global robotics industry was forecast to expand from $34 billion to $226 billion by 2021.
So how did a company like Orbotech respond to these trends and provide solutions for the PCB industry? Alliston described latest developments in direct imaging for HDI, mSAP and solder mask, with particular emphasis on achieving registration accuracy and high throughput. He discussed new concepts in AOI with integrated 2D metrology, and how the needs of Industry 4.0 were supported with a smart factory metrology package offering full product traceability for root cause analysis and life cycle control.
Page 2 of 3
Suggested Items
Indium Experts to Present on High-Temperature, Lead-Free Solder Paste and High Reliability Liquid Metal Alloys Poster at ECTC
05/16/2024 | Indium CorporationIndium Corporation Research Associate Kyle Aserian will deliver a presentation at the 74th Electronic Components and Technology Conference (ECTC) on May 31, in Denver, Colorado.
Indium Experts to Present at Electronics in Harsh Environments SMTA Conference
05/13/2024 | Indium Corporationndium Corporation Technical Manager for Europe, Africa, and the Middle East, Karthik Vijay, will deliver a technical presentation and Indium Corporation Senior Technologist, Dr. Ronald Lasky, will deliver both a workshop and technical presentation at the Electronics in Harsh Environments SMTA Conference on May 14-16 in Copenhagen, Denmark.
Connect the Dots: Designing for Reality—The Pre-Manufacturing Process
05/08/2024 | Matt Stevenson -- Column: Connect the DotsI have been working with Nolan Johnson on a podcast series about designing PCBs for the reality of manufacturing. By sharing lessons learned over a long career in the PCB industry, we hope to shorten learning curves and help designers produce better boards with less hassle and rework. Episode 2 deals with the electronic pre-manufacturing process. Moving from CAD (computer-aided design) to CAM (computer-aided manufacturing) is a key step in PCB manufacturing. CAM turns digital designs into instructions that machines can use to actually build the PCB.
AIM Solder Signs Shinil Fl Ltd. as New Distributor for Korea
05/08/2024 | AIM SolderAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce a new distribution partnership with Shinil Fl Ltd., a prominent supplier of technological solutions in the SMT and semiconductor sectors.
Indium Corporation to Showcase HIA Materials at ECTC
05/07/2024 | Indium CorporationAs an industry leader in innovative materials solutions for semiconductor packaging and assembly, Indium Corporation® will feature its advanced products designed to meet the evolving challenges of heterogeneous integration and assembly (HIA) and fine-pitch system-in-package (SiP) applications at the 74th Electronic Components and Technology Conference (ECTC), May 28‒31, in Denver, Colorado.