Three Industry Giants From WKK Gather Around for Discussion


Reading time ( words)

During the recent HKPCA show I had the opportunity to catch up with Hamed El-Abd, Lionel Fullwood, and Gene Weiner. Our discussion covered an array of topics, from politics to new PCB factories and what it takes to stay competitive. Below is the transcription from our conversation.

007: Here with me today is Hamed El-Abd, Lionel Fullwood and Gene Weiner from WKK, welcome guys.

GW: Barry, it’s good to see you again in China, the number one economy in the world as of this quarter.

007: Thank you, and that’s what I’ve read just this morning.

GW: And that is clearly because of numbers, not because of technology. The leading technology here is still coming in from the foreigners, including the Taiwanese, who are classed as foreigner.

007: Gene you’ve been coming to China for many years now, correct?

GW: Since 1983.

007: One of the things that strikes me is the amount of change that has happened in just the last five years in particular. What changes have you seen and what’s your opinion on it?

GW: Well with the change a lot of it is superficial. Much of it is a new younger government tightening up, and much of it is from a stronger economic position globally and a stronger military. The Chinese have put themselves in a position to be a power player, if not the power player in the world. They’re still copying, copying, copying and not paying much attention to specs. Mostly it’s homegrown products for homegrown companies, with the best technology still coming from Europe, the U.S., Japan and Taiwan. From Taiwan I would say it’s the application of the technology improvements done by ITRI, their government sponsored research, as well as their major companies.

007: In comparison to the U.S., where obviously you've spent a lot of time, what do you see happening from your point of view?

GW: The U.S. is struggling to maintain a position with a government that appears confused with economic, domestic, and foreign policies. However, quietly happening in the U.S., and not for volume but for technology, we're seeing some great advances in R&D in chips, packages, chipsets, as well as the quiet building of new automated factories in captive shops not publicly known. Lockheed has three in-house printed circuit shops and the public thinks there's only one. It’s now become an open secret that Intel is building a shop in Chandler. Two weeks ago Lionel and I visited Whelen’s new factory in New Hampshire and it’s the first fully automated new printed circuit shop in North America—and I really mean fully automated. The only things that were not part of the automation line was a separate semi-automatic layup set-up and multilayer pressing line by Burkle, an offline ENIG electroless nicke/gold and a plasma machine. Everything else was inline, automated, with a very modern design. Instead of treating the air and water of the entire building they use semiconductor techniques with tunnels around the equipment, making it easier to maintain the environment, and they didn't have to get one single permit for waste treatment because the plant is almost 100% total recycle of air, fumes, and liquid. Copper is plated out of the spent etchant, the ammonia is recaptured and put back in—it was amazing. And we were watching the first runs of 100 panel lots when we were there, and Lionel is doing some evaluation of some new imaging equipment which we can't give you the details on until perhaps spring. 

007: Are they in production now?

Share

Print


Suggested Items

EIPC Technical Snapshot: PCB Surface Finishes

12/28/2020 | Pete Starkey, I-Connect007
For the third in a series of Technical Snapshot webinars, EIPC chose to focus on PCB surface finishes, comparing specific properties, examining corrosion behaviour and discussing selection criteria for low-loss, high frequency applications.

Prices of Copper-Clad Laminates Continue to Rise

12/18/2020 | I-Connect007 China Team
Forces within and outside the PCB industry have led to concerns over rising prices for raw materials of copper-clad laminates (CCL). Recently, two major explosions at epoxy resin plants in China had a great impact on domestic resin suppliers. Prices have risen steadily in 2020, with leading CCL manufacturers announcing price increases of 20-30% recently. As the cost of raw materials such as electronic copper foil, resin and glass fiber have risen, the cost for manufacturing CCL has taken off as well.

Happy Holden: ECWC15 Virtual Event a Success

12/15/2020 | Happy Holden, I-Connect007
This is the first Electronic Circuits World Convention that I have not attended in person since 1978. To refresh your memory, these are held every three years on a rotating basis. The HKPCA hosted this year’s conference and they kept up the fine tradition of collecting outstanding keynotes, nearly 60 technical presentations and myriad poster papers. HKPCA was also kind enough to provide English slides and translations. It is still possible to sign up and view the presentations. I have listened to 20 of the presentations, and hope to attend even more in the coming days as they are all worth watching.



Copyright © 2021 I-Connect007. All rights reserved.