-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueThe Growing Industry
In this issue of PCB007 Magazine, we talk with leading economic experts, advocacy specialists in Washington, D.C., and PCB company leadership to get a well-rounded picture of what’s happening in the industry today. Don’t miss it.
The Sustainability Issue
Sustainability is one of the most widely used terms in business today, especially for electronics and manufacturing but what does it mean to you? We explore the environmental, business, and economic impacts.
The Fabricator’s Guide to IPC APEX EXPO
This issue previews many of the important events taking place at this year's show and highlights some changes and opportunities. So, buckle up. We are counting down to IPC APEX EXPO 2024.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - pcb007 Magazine
Alpha Takes the Greenfield Route
February 28, 2023 | Nolan Johnson, I-Connect007Estimated reading time: 2 minutes
Alpha Circuit is a PCB fabricator located in Elmhurst, Illinois. Given that the launch of a new PCB fab is a rare occasion these days, we caught up with the senior team—Prashant Patel, president and CEO; Steve Smith, general manager; Steve Ryan, sales and direct support—guiding the buildout of Alpha Circuit’s brand new 44,000 square foot facility. They discuss what goes into equipment selection and line design, and the timing couldn’t have been better. At press time, the new facility was on schedule for test production by the end of January 2023.
Throughout the conversation, the Alpha team shared its methods for designing the facility, the parts of the fabrication process that are critical to get exactly right, and where the surprises were in the process.
Nolan Johnson: Gentlemen, welcome, and congratulations on your new facility. Let’s start with a little background about the company.
Steve Ryan: Alpha Circuit started in 1981, as a single- and double-sided board shop. Zenith was one of our big customers early on. We did a lot of punching and crunching back then and it is what really catapulted the revenue stream for us. When I joined the company in 2009, we were comfortably an eight to 12-layer multilayer and double-sided manufacturer. In 2013, we started doing flex and rigid-flex, increased our multilayers up to 28 layers, and started manufacturing copper-based pedestal-type design work.
Prashant Patel: When I acquired the company in 2020, my vision was to continue Alpha Circuit the way it was, while building a new facility to meet the higher technology demands. We purchased and renovated a 44,000 square foot facility, then ordered the equipment. It takes a long time to source equipment—you get the quotes, have it installed, and then get it running up to speed. That process has taken us over three years.
Steve Smith: I joined the company approximately two months ago. My background is HDI: stacked microvias, staggered microvias, along with high-speed digital materials, low-loss materials. I was hired to put the technology part of it together, getting the proper people and processes in place, so we can handle microelectronics down to 25-micron line and space and down to 3-mil pads.
Johnson: Great, thank you for that. Now, I want to talk today about your recent equipment purchases.
Smith: We have purchased a laser drill, and we have brand-new 200,000 RPM drill machines in place to do high aspect ratio holes. We also have a brand-new plating line with state-of-the-art chemistries to be able to do copper fill and through-hole plating in the same process along with being able to manufacture stacked vias starting with a 2-mil core substrate and stacking up to seven or eight lamination cycles.
To read this entire conversation, which appeared in the February 2023 issue of SMT007 Magazine, click here.
Suggested Items
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.